Alexor PC9155G-868 Guide d'installation télécharger pdf (Page 10)

PC9155 Wireless Alarm System

2-3

2.2 Wiring

1 I/O Wiring

The two I/O terminals can be programmed as hard-wired zone inputs and/or PGM outputs. See programming section [013] Opt [1,2].

1a. Zone Wiring

Zones 1 - 32 are reserved for wireless zones. If programmed as zone inputs, I/O-

1 is zone 33 and I/O-2 is zone 34.

Zones can be wired for Normally Open (NO) contacts with single-end-of-line

resistors or Normally Closed (NC) contacts with single-end-of-line or double-

end-of-line resistors.

Observe the following guidelines:

• For UL/ULC listed installations use SEOL or DEOL only

• Use minimum 22AWG, maximum 18 AWG wire

• DO NOT use shielded wire

• Wire run resistance shall not exceed 100

Ω

Zones 33 and 34 are defaulted for SEOL resistors

• Section [133]-[134] opt.[14] selects Normally Closed or Normally Open

• Section [133-[134] opt.[15] selects SEOL resistors

• Section [133]-[134] opt.[16] selects DEOL resistors

Zone Status - Loop Resistance/Loop Status (DEOL only)

• Fault - 0

Ω (shorted wire/loop)(shorted wire to 4.5KOhm)

• Secure - 5,600

Ω (contact closed)(4.5KOhm to 6.25KOhm)

• Violated - 11,200

Ω (contact open)(13.5KOhm to open)

• Tamper - infinite (broken wire, open)(9KOhm to 13.5KOhm)

1b. Programmable Output (PGM) and Aux Wiring

I/O terminals configured as programmable outputs (PGMs) switch to ground

when activated by the alarm system. The PGMs are open collector outputs. With

a 45 mA load, the voltage measured at the PGM and Aux + shall be approxi-

mately 8V with respect to ground. With a 25 mA load, the voltage measured shall

be approximately 10V.

Connect the positive side of the device to the Aux+ terminal.

Connect the negative side of the device to the I/O terminal.

Each PGM can provide 50mA maximum output.

NOTE:

The PC9155 provides 200mA maximum of AUX current for PGMs, relays,

LEDs, etc. The AUX output shall be used only for residential burglary applications.

LED output with:

Current limiting resistor and

optional relay driver output.

Compatible initiating devices intended

to be used on the AUX output shall be

rated for the range: 9.6VDC to

13.8VDC min.

1c. PC5950 2-Way Audio Verification Module Wiring

• Install the PC5950 in a metal cabinet secured to a wall.

• Power down the PC9155 if required.

• Route wiring to the PC9155 through the wiring guide.

• Route wiring to the audio stations as indicated (2 Max).

• Ensure telephone line wiring enables the PC9155 to seize the line.

• Test the system. Refer to the PC5950 Installation Guide.

Refer to Appendix C: 2-Way Audio Verification (PC5950).

Program I/O 1

- Audio Verification PGM

Program I/O 2

- Audio Verification Monitor Zone

Normally Closed Loops - Do NOT use for UL Installations

Any I/O

Terminal

Double End-of-Line Resistor Wiring

AUX-

Terminal

2 NORMALLY CLOSED

CONTACTS WITH

NO END OF LINE

RESISTOR

1 NORMALLY CLOSED

CONTACT WITH

NO END OF LINE

RESISTOR

Single End-of-Line Resistor Wiring

1 NORMALLY

CLOSED

CONTACT WITH

5600Ω

END OF LINE

RESISTOR

1 NORMALLY OPEN

CONTACT WITH

5600 Ω

END OF LINE RESITSTOR

1 NORMALLY OPEN

CONTACT AND

1 NORMALLY CLOSED

CONTACT WITH

5600Ω END OF LINE

RESISTOR

2 NORMALLY OPEN

CONTACTS AND

2 NORMALLY CLOSED

CONTACTS WITH

5600Ω END OF LINE

RESISTOR

ALARM

CONTACT

DEOL CIRCUIT

1 NORMALLY

CLOSED CONTACT

WITH 5600Ω

END OF LINE RESISTORS

ALARM

CONTACT

DEOL CIRCUITS

2 NORMALLY

CLOSED CONTACTS

WITH 5600Ω END

OF LINE & TAMPER

RESISTOR

TEMPER

CONTACT

Any I/O

Terminal

Any I/O

Terminal

Any I/O

Terminal

Any I/O

Terminal

Any I/O

Terminal

Any I/O

Terminal

Any I/O

Terminal

AUX-

Terminal

AUX-

Terminal

AUX-

Terminal

AUX-

Terminal

AUX-

Terminal

AUX-

Terminal

AUX-

Terminal

Burglary Zone Wiring Chart

Wire Size Max wire length to end-of-line resistor

AWG mm Feet Meters

22 0.65 3000 914

20 0.81 4900 1493

19 0.91 6200 1889

18 1.02 7800 2377

Figures are based on maximum wiring resistance of 100 Ω

I/O

3&

$8;

,2

,2

<HO

3&

$8;

%ON

%HOO

5HG

%HOO

*UQ

2II

.

$/0

2II

.,662II

,2

,2

<HO

$8;

%ON

%HOO

5HG

%HOO

*UQ

2II

$/0

2II

.,662II

&20

7DON/LVWHQZLWK6LUHQ6KXWGRZQ

/LVWHQLQ2QO\ZLWK6LUHQ6KXWGRZQ

5LQJ

5

7

7LS

)URP

2XWVLGH

3KRQH/LQH

7R+RXVH

3KRQHV

5LQJ

5

7

7LS

3&

3&

5LQJ

5

7

7LS

)URP

2XWVLGH

3KRQH

/LQH

7R+RXVH

3KRQHV

5LQJ

5

7

7LS

PC5950 Programming

Section 01 - Set to 1 (Hard Trip)

Section 10 - Set to 2 (Trigger

Enable:Auto Trip by Bell or Green)

PC5950 Programming

Section 01 - Set to 1 (Hard Trip)

Section 07 - Set to 1 (Trigger High)

Section 10 - Set to 2 (Trigger Enable:

Auto Trip by Bell or Green)

Wiring diagram 1, Talk/Listen with Siren Shutdown, does a full talk/

listen in session for silent alarms. If a listen-in only session is

required for silent alarms, use wiring diagram 2, Listen-in Only with

Siren Shutdown.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 79 80

Commentaires sur ces manuels

Pas de commentaire

Alexor PC9155G-868 Guide d'installation Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Alexor PC9155G-868