Alexor PT4 Manuel d'utilisateur Page 11
- Page / 27
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
7
Door Chime
To turn the door chime function on or off, press and hold the Chime button for 2 seconds or
press . The system will sound 3 beeps to indicate the door chime is on, or one long tone
to indicate that door chime is off.
Access Code Programming
In addition to the master code, you can program up to 16 additional user access codes. If wire-
less keys have been programmed then wireless key #1 will log as User Access Code #1 (if that
access code has been programmed). User Access Codes 1-16 will correspond to wireless keys
or prox tags 1-16. Press [Master Access Code]; the armed ( ) indicator will turn on.
Enter the 2-digit number to be programmed (e.g., 06 for User Access Code 6; enter 40 for the
master access code) or press the scroll buttons to find the specific code and press
to select. Enter the new 4-digit access code. When programming is complete, enter
another 2-digit code to program or press to exit. The access codes have programmable
attributes which allow zone bypassing, duress, supervisor, remote access, or one-time use acti-
vation.
On WT5500P keypads, you will be prompted to swipe a prox tag once the last character of the
access code is entered. To delete prox tags, the associated user access code must be deleted
as described, then re-programmed if required.
Access Codes [][5][Master Code] (when disarmed)
The [][5] User’s Programming command is used to program additional access codes.
User Codes - User codes 1-16 are available for the system.
Master Code (Access Code 40) - The master code has all of the attributes listed in the Pro-
grammable Attributes list below except for Duress (2) and One-Time Use (8) and is required to
program all supervisor code attributes.
Supervisor Codes - These codes are always valid when entering the User Code Pro-
gramming or User Function sections. However, these codes can only program addi-
tional codes which have equal or lesser attributes. Once programmed, the supervisor codes
receive the master code’s attributes. These attributes are changeable. Any user code can be
made a supervisor code by enabling User Code Attribute 1 (please see below for details).
Duress Codes - Duress codes are standard user codes that will transmit the Duress Alarm
Reporting Code whenever the code is entered to perform any function on the system. Any user
code can be made a duress code by enabling User Code Attribute 2 (see below for details).
One-Time Use Code -
This code permits temporary access to the system for a 24-hour time
period. During the 24hr period, the temporary user may disarm the system once. There is no
restriction on the number of times the temporary user may arm the system during the time period.
NOTE: Duress codes are not valid when entering [][5], [][6] or [][8] sections.
NOTE: Access codes cannot be programmed as a duplicate or as a "Code +/- 1".
User Code Attributes
1. The default attributes of a new code will be the attributes of the code used to enter
whether it is a new code or an existing code being programmed.
2. System Master (Code 40) has Attribute 3 on by default.
NOTE: These attributes are not changeable.
Inherent Attributes (all codes except installer)
Arm / Disarm - Any access code will be valid for arming and disarming the system.
Command Outputs ([][7][1] and [][7][2]) - If these outputs require access code entry, any
access code is valid for performing the [][7][1-2][Access Code] functions on the system.
Programmable Attributes ([][5][Master/Supervisor Code][9][Code])
1 Supervisor Code 5-6 For Future Use
2 Duress Code 7 Bell/Siren Squawk upon Away Arming/Disarming
3 Zone Bypassing Enabled 8 One-Time Use Code
4 Remote Access
- User Manual 1
- FCC COMPLIANCE STATEMENT 2
- Table of Contents 3
- IMPORTANT SAFETY INSTRUCTIONS 4
- CLEANING 4
- TROUBLESHOOTING 4
- About Your Security System 5
- System is 6
- Ready to Arm 6
- Silent Exit Delay 7
- Away Arming 7
- Quick Exit 7
- Disarming 7
- HH:MM MM/DD/YY 8
- 09:06 01/31/10 8
- To program a Bypass Group: 9
- Trouble Conditions 10
- Alarm Memory 10
- User Code Attributes 11
- Zone Bypassing Attribute 12
- Remote Access Attribute 12
- Bell/Siren Squawk Attribute 12
- Erasing an Access Code 12
- Ambient Light Sensor 13
- Changing the Buzzer Level 13
- Changing Brightness/Contrast 13
- To lock the keys: 16
- To unlock the keys: 16
- Keypad Low Battery 17
- Keypad Battery Replacement 17
- Reference Sheets 18
- Sensor / Zone Information 19
- SMS Telephone Numbers 19
- Status Lights 20
- Function Keys 20
- Special Keys 20
- User Commands 20
- Smoke Detectors 22
- Carbon Monoxide Detectors 23
- Household Fire Safety Audit 24
- Fire Escape Planning 24
- WARNING Please Read Carefully 26
- 29007633R001 27
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Alexor PT4
(32 pages)
Flowserve Heavy Duty Gear Override Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Hardware Flowserve Heavy Duty Gear Override.
Wir stellen 1 PDF-Handbücher Flowserve Heavy Duty Gear Override zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels